Gas Analyzer Micro Small DC3.0V Electric Vacuum Pump

In gas detectors, Electric Vacuum Pump, as an important component, play a key role. It can provide stable pumping power, thereby helping the gas detector achieve accurate measurements. The following is some common knowledge about the use of Mini Vacuum Pump in gas detectors:

1.Pump selection

When choosing a Mini Electric Vacuum Pump, you need to consider the following factors:

·Pumping volume: According to the model and purpose of the gas detector, select the appropriate pumping volume to ensure that it can meet the needs of the equipment.

·Working pressure range: Understand the working pressure range of the micro diaphragm vacuum pump to ensure that it can operate within the normal working range of the gas detector.

·Noise level: If the gas detector needs to be used in a quiet environment, a micro diaphragm vacuum pump with lower noise should be selected.

Power requirements: Confirm the power requirements of the micro diaphragm vacuum pump to ensure compatibility with the gas detector's power supply.

·Other characteristics: If special requirements such as long-term continuous operation and explosion-proof are required, a miniature diaphragm vacuum pump with corresponding characteristics should be selected.

2. Working principle of DC Electric Vacuum Pump

Micro Electric Vacuum Pump usually uses a reciprocating design, using a diaphragm that moves back and forth to suck in and discharge gases. When the diaphragm moves in one direction, the air inlet of the pump is opened and gas is sucked into the pump; when the diaphragm moves in the other direction, the air inlet is closed, and the gas in the pump is compressed and discharged from the air outlet. The working principle of the miniature diaphragm vacuum pump ensures that it can provide stable pumping power.

3. DC Pump Maintenance

In order to ensure the normal operation and service life of the micro electric vacuum pump, regular maintenance is required:

·Cleaning: Regularly clean the outer surface and internal parts of the micro diaphragm vacuum pump to prevent the impact of dust and dirt.

·Lubrication: Regularly lubricate the bearings, shaft seals and other moving parts of the micro diaphragm vacuum pump to reduce wear and maintain flexible operation.

·Check the fasteners: Regularly check whether the fasteners of the micro diaphragm vacuum pump are loose. If looseness is found, tighten them in time.

·Replace worn parts: If the diaphragm, bearings and other parts are found to be seriously worn or damaged, they should be replaced in time.

Technical parameter       

4. Pump troubleshooting

If the micro diaphragm vacuum pump fails, you can take the following measures to troubleshoot:

.Check the power connection: Confirm whether the power connection of the micro diaphragm vacuum pump is normal. If there are open circuits, short circuits and other problems, they should be solved in time.

.Check the exhaust port: Observe whether the exhaust port of the Dc Mini Vacuum Pump exhausts normally. If problems such as exhaust port blockage occur, clean or replace relevant parts in time.

.Check the status of the diaphragm: Check whether the diaphragm of the Portable Vacuum Pump is damaged or broken. If these problems occur, replace the diaphragm in time.

.Check the bearings and lubrication status: Check whether the bearings and lubrication status of the miniature diaphragm vacuum pump are in good condition. If there are problems such as severe bearing wear or poor lubrication, the bearings should be replaced in time or the lubrication status should be improved.

Performance Chart                                                       

Mini Pumps and mini valves application

What is the specific role of micro Membrane Vacuum Pump in gas detection?

In gas detection, micro diaphragm vacuum pumps can be used to extract gas samples to be detected from the environment and send them to gas detection instruments for analysis.

At the same time, the micro diaphragm vacuum pump can also be used to accelerate filtration, vacuum adsorption, vacuum filtration and other processes, making gas detection more efficient and accurate.

In addition, micro diaphragm vacuum pumps can also be used for pumping and pumping. For example, in the medical field, they can be used to extract gases from patients for analysis, or in the industrial field, they can be used to provide power sources for gas analysis instruments.